Sealey PP100 Manuel d'utilisateur télécharger pdf (Page 1)

1. SAFETY INSTRUCTIONS

INSTRUCTIONS FOR:

POWER SCAN AUTOMOTIVE

PROBE/SCOPE 0-30V

MODEL No: PP100

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND

CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO

MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

2. INTRODUCTION AND DESCRIPTION

2.2 Description (fig.1)

2.2.1 Probe Tip – Contacts the circuit or component to be

tested.

2.2.2 Work Lights – Illuminate work area.

2.2.3 Red/Green Polarity Indicator – Identifies positive,

negative or open circuits. The red indicator lights

when the probe tip is contacting a positive circuit.

The green indicator lights when the probe tip is

contacting a negative circuit.

2.2.4 LCD Display

2.2.5 Circuit Breaker Reset – Resets the tool when the

circuit breaker is tripped

2.2.6 Power Switch – When operated conducts a positive

or negative battery current to the tip for activating

and testing the function of electrical components.

2.2.7 Mode Button – Selects the work mode: DC voltage,

scope, resistance & audible indicator.

2.2.8 Speaker – When the audible indicator is turned on,

emits a tone.

2.2.9 Auxiliary Ground Lead

2.2.10 Adaptor – Connects to the battery supply via clips or

cigarette lighter adaptor.

2.1 Introduction

Probably the most advanced automotive probe on the

market, with a huge range of functions for effective

automotive diagnostics, making short circuits and bad

earths easy to nd. Features a scope function to

visually test component signals, with the added benet of

maximum/minimum volts, frequency and duty cycle

displayed. Allows components to be activated in situ or

prior to installation. The y lead allows continuity and

polarity testing with a high-contrast colour LCD display

giving a 7mm high read-out. Features audible and posi-

tive/negative voltage indicator and two integral work lights.

6mtr lead connects to the battery supply and reaches all

areas of the vehicle. Includes a vehicle accessory socket

adaptor. Supplied in carry-case.

Original Language Version

PP100 Issue: 2 - 06/03/12

g.1

 IF YOU ARE IN ANY DOUBT ABOUT ELECTRICAL

SAFETY CONSULT A QUALIFIED ELECTRICIAN.

 Only for use with 2V - 24V DC systems.

 DO NOT apply voltage or current to the probe that

exceeds the specified maximum of 30V DC.

 DO NOT use with industrial 110V systems.

 DO NOT use on any circuit directly or indirectly

connected to AC lines or any other AC power

source.

 DO NOT use with any component or circuits on the

vehicle’s ignition system.

 Before using this device, check the vehicle’s

electrical wiring and disconnect any part or system

sensitive to voltage and current pulses such as air

bags, electronic control modules, etc.

 Always check the instructions and procedures

indicated in the vehicle service manual before

attempting to disconnect any part or sub-system of

the electrical circuit.

 When not in use, store carefully in a safe, dry,

childproof location. Avoid extremes of temperature.

 DO NOT use the tool around explosive gases,

vapour or dust. When the power switch is operated

(forwards or backwards), battery current is

conducted to the tip of the probe which may cause

sparks when contacting ground or certain other

circuits.

 DO NOT use leads if damaged or if the wire is

bared in any way.

 DO NOT use the equipment when you are tired or

under the influence of alcohol, drugs or intoxicating

medicines.

 DO NOT use this tool for any purpose other than

that for which it has been designed.

1 2 3 4 5 6

Résumé du contenu

Page 1 - PROBE/SCOPE 0-30V

1. SAFETY INSTRUCTIONSINSTRUCTIONS FOR: POWER SCAN AUTOMOTIVE PROBE/SCOPE 0-30VMODEL No: PP100Thank you for purchasing a Sealey product. Manufactured

Page 2 - 3. OPERATION

3. OPERATION Original Language VersionPP100 Issue: 2 - 06/03/123.1 Basic Connections (fig.2)3.1.1 Unroll the probe cable. Connect the red battery

Page 3 - 4. TESTING PROCEDURES

Original Language VersionPP100 Issue: 2 - 06/03/124.2 Continuity Testing4.2.1 While the probe is in resistance mode, continuity can be tested o

Page 4 - Original Language Version

Original Language VersionPP100 Issue: 2 - 06/03/124.3 Signal Circuit Testing4.3.1 The tool can be used as a trouble shooting aid to test sensor

Page 5

Original Language VersionPP100 Issue: 2 - 06/03/124.6 Activating Components With a Positive (+) Voltage Within Vehicle Electrical System 4.6.1 S

Page 6 - 5. MAINTENANCE

Environmental Protection. Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted

Commentaires sur ces manuels

Pas de commentaire

Sealey PP100 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Sealey PP100. Sealey PP100 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Sealey PP100 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Sealey PP100. Sealey PP100 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Sealey PP100