Sealey CVS18 Manuel d'utilisateur télécharger pdf

INSTRUCTIONS FOR:

UNIVERSAL SPLIT CVJ BOOT

Ø56-120mm

Model No: CVS18

1. SAFETY INSTRUCTIONS

2. INTROdUCTION & SPECIFICATIONS

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give

you years of trouble free performance.

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE TOOL CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

 WARNING! Ensure Health and Safety, local authority and general

workshop practice regulations are adhered to when using tools.

 Ensure that a vehicle which has been jacked up is adequately

supported with axle stands and that the wheels are chocked,

refer to the vehicle manufacturer’s service instructions, or a

proprietary manual.

 Wear approved eye protection. A full range of personal safety

equipment is available from your Sealey dealer.

 Wear suitable clothing to avoid snagging. Do not wear jewellery

and tie back long hair.

 IMPORTANT: This manual is provided as a guide only, refer

to the vehicle manufacturer’s service instructions, or a

proprietary manual, to establish the current procedure and

data.

 WARNING! Failure to heed safety and warning instructions may

result in damage and/or personal injury and will invalidate the

warranty.

 WARNING! The warnings, cautions and instructions

referred to in this manual cannot cover all possible

conditions and situations that may occur. It must be

understood that common sense and caution are factors

which cannot be built into this product, but must be

applied by the operator.

3. OPERATION

3.1. Access will be improved by removal of the wheel and brake

caliper, although this is not essential.

3.2. Check the size required for your CVJ boot. Remove the old boot

and assess the required size by measuring it, and the CV joint

once it has been cleaned.

3.3. Wipe away the old grease. If the CV joint contains water or dirt,

 cleanitasmuchaspossible.Cleanthedriveshaftandange 

thoroughly. If the working area is awkward, wrap the joint

 andshaftinlm,suchasClinglmoraseatprotectortoavoid 

contaminating the new boot with grease.

3.4. Wash and dry your hands thoroughly. The following steps cannot

 bedonewithoilyorwethands.Beforeglueing,practicetting 

the boot joint faces together, 1 or 2 centimetres at a time,

starting with the small end. Don’t try to hold the whole seam

together, it is almost impossible without the glue.

3.5. Put on the rubber gloves provided. Stretch the boot at the small

end. There is no risk of tearing the rubber. Put the small end

of the boot around the shaft. Stretch the boot at the small end,

pulling each side around the shaft so that it overlaps at the join if

you can. Hold it overlapped for a few seconds to take the tension

out of the rubber.

3.6. Starting at the small end, smear a little glue across the joint face

 andllthegrooveforabout2centimetres,tothestartoftherst

convolution. Now make the joint carefully, readjusting until the

tongue and groove are neatly settled in. Hold the join still for

 about60secondstoallowthegluetoset.Ensurethatngersare

kept well clear of the glue to avoid accidental adhesion.

3.7. In very cold or very dry weather allow a little more time for the

glue to set. Release carefully to make sure the joint has taken. If

glue has squeezed out and formed a blob on the surface, it will

take time to harden but the join will not be affected. Scrape away

the excess glue with a piece of card at the end of the job.

3.8. Glue the next 2 centimetres and assemble in the same way. As

it is not under tension, it only needs to be held together for 20

seconds. Repeat to the end of the boot, then allow the glue to

cure for 20 minutes.

3.9. Cut the corner of the grease sachet and direct the grease into

the joint. There is no need to put grease into the boot, but it

doesn’t matter if you do – once made, the glued joint is not

affected by the grease.

3.10. FitthebootovertheCVjointandtthetiessecurelyatboth 

ends. Ensure that any components removed from the vehicle are

replaced securely before lowering.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Sole UK distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

CVS18 Issue: 1 24/01/14

01284 757500

01284 703534

sales@sealey.co.uk

www.sealey.co.uk

Web

Universal CV boot made from high quality neoprene that is resistant to

grease, water, ozone, abrasion and extremes of temperature. Suitable

for 98% of cars and car derived vans. No dismantling of joint/shaft re-

quiredandttedin20minutes.Suppliedwithttingkitincludingclips,

grease sachet, disposable gloves, glue and cutting guide.

Model No: CVS18

Joint Diameter: 56-120mm

Shaft Diameter: 19-35mm

Environmental Protection.

Recycle unwanted materials instead of disposing of them as

waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of in a manner which

is compatible with the environment.

UNIVERSAL SPLIT CVJ BOOT 1
Ø56-120mm 1

Résumé du contenu

Page 1 - Ø56-120mm

INSTRUCTIONS FOR:UNIVERSAL SPLIT CVJ BOOT Ø56-120mmModel No: CVS18 1. SAFETY INSTRUCTIONS 2. INTROdUCTION & SPECIFICATIONSThank you for purchas

Commentaires sur ces manuels

Pas de commentaire

Sealey CVS18 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Sealey CVS18. Sealey CVS18 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Sealey CVS18