Sealey TC967 Manuel d'utilisateur télécharger pdf

 IMPORTANT! Never attempt to fit or remove a tyre without first lubricating

both beads.

3.1 Bead breaking

3.1.1 Deflate the tyre by removing the valve core and remove all balance weights.

3.1.2 Place the wheel with the valve facing down, over the threaded centre bar (fig.1).

3.1.3 Thread the locking nut onto the threaded centre bar, using the alignment cone and optional spacers if required.

Note: Ensure that the wheel is securely fastened to the tyre changer before proceeding with the operation.

3.1.4 Attach the bead breaker to the locking nut using one of the locking pins.

3.1.5 Adjust the shoe of the bead breaker so that it sits on the tyre and aligns close to the edge of the wheel rim and locate using the other

locking pin (fig.2).

3.1.6 Apply firm pressure to the bead breaker by pushing down on the long handle, gradually work around the wheel rim until the bead has

separated from the rim.

3.1.7 Turn wheel over and repeat to free the other bead.

3.1.8 Remove the bead breaker bar from the locking nut.

3.2 Tyre removal

3.2.1 Lubricate both tyre beads with an approved rubber lubricant.

3.2.2 Place the wheel onto the stand with the narrow bead seat uppermost and lock down using the lock nut and spacers.

3.2.3 Push down on the tyre until there is enough room to insert the ball end of the tyre removal tool under the bead of the opposite side of

the tyre (fig.3).

3.2.4 Push down on the removal bar, so that the bead is raised above the rim.

3.2.5 Hold the tyre to prevent it from turning and pull the removal bar around anti-clockwise until all the bead has been raised above the

rim (fig.3).

3.2.6 Lift the tyre up, remove inner tube if fitted and repeat the procedure for the lower bead (fig.4).

INSTRUCTIONS FOR:

MINI TYRE CHANGER

MODEL: TC967

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

TC967 Issue No: 1 - 21/10/08

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. SPECIFICATIONS

3. OPERATION

TC967

Suitable for changing tyres with small rim diameters commonly found

on agricultural, leisure and industrial vehicles such as ATV’s, golf

buggies, mowers, garden tractors and handling equipment. Mount

directly onto work surface. Supplied with tyre bar and alignment cone.

1.2 GENERAL SAFETY

 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.

Under Health and Safety Law, Employers and Self Employed Personnel have a legal duty to ensure Safe Working Conditions for all

employees and personel that may come into contact with this equipment. In particular they must carry out a specific risk and hazard

assessment in the workplace to eliminate or reduce any risk found and must record, update and retain records of the results of this

inspection.

 Familiarise yourself with the applications, limitations and any possible or potential hazards of the tyre changer.

 Maintain the tyre changer in good condition (use an authorised service agent).

 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 WARNING! Check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is next used.

 Locate the tyre changer in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure that there is adequate

lighting.

 WARNING! The tyre changer must be bolted to a work surface. For best results mount the Mini Tyre Changer at waist height.

 Keep the tyre changer clean for best and safest performance.

 Wear approved safety eye protection.

 Keep hands well clear of the bead breaker.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip safety shoes.

 Remove ill fitting clothing. Remove ties, watches, rings other loose jewellery and contain and/or tie back long hair.

 Keep children and unauthorised persons away from the work area.

 DO NOT use the tyre changer for any purpose other than that for which it is designed.

 DO NOT operate the tyre changer if any parts are damaged or missing as this may cause failure and/or personal injury.

 DO NOT allow untrained persons to operate the tyre changer.

 DO NOT stand on the tyre changer.

 DO NOT operate the tyre changer when you are tired or under the influence of

alcohol, drugs or intoxicating medication.

Minimum Rim Size: 100mm

Maximum Rim Size: 300mm

Maximum Wheel Width: 150mm

1 2 3

Résumé du contenu

Page 1 - MINI TYRE CHANGER

 IMPORTANT! Never attempt to fit or remove a tyre without first lubricating both beads.3.1 Bead breaking3.1.1 Deflate the tyre by removing the v

Page 2 - 01284 703534

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prio

Page 3

Commentaires sur ces manuels

Pas de commentaire

Sealey TC967 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Sealey TC967. Sealey TC967 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Sealey TC967