Sealey AK396 Manuel d'utilisateur télécharger pdf

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

INSTRUCTIONS FOR:

THREADED NUT RIVET KIT

Model No: AK396.V2

AK396.V2 - 1 - 071205

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND

CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY

CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. SPECIFICATION AND CONTENTS

! WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.

" Familiarise yourself with the application and limitations of the riveter, as well as the potential hazards.

" Maintain the riveter in good condition (use an authorised service agent).

" Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

" Keep the work area clean, uncluttered and ensure there is adequate lighting.

" Keep the riveter clean for best and safest performance.

! WARNING! Always wear approved eye or face protection when operating the riveter.

" Keep children and unauthorised persons away from the working area.

" Check moving parts alignment on a regular basis.

# DO NOT hold the workpiece by hand. Secure unstable workpiece with a clamp, vice or other adequate holding device.

" Ensure the workpiece is correctly secured before operating the riveter.

# DO NOT use the riveter for any purpose other than that for which it is designed.

# DO NOT operate the riveter if any parts are damaged or missing, as this may cause failure and/or personal injury.

" When not in use return to the case and store in a safe, dry, childproof area.

Suitable for rivets, rivet nuts and rivet studs in aluminium, steel and stainless steel. Swivel head with 360° movement gives greatly improved

accessibility. Four nozzles for standard rivets, four mandrels for rivet nuts and three mandrels for rivet studs. Supplied with spanners and a

selection of steel rivet nuts.

The AK396 kit is suitable for fitting the following size rivet, rivet nuts and rivet studs.

Rivets 2.4mm (3/32”) 3.2mm (1/8”) 4.0mm (5/32”) 4.8mm (3/16”)

Rivet Nuts M3 x 0.5 M4 x 0.7 M5 x 0.8 M6 x 1.0

Rivet Studs

# M4 x 0.7 M5 x 0.8 M6 x 1.0

fig. 1

CONTENTS

1. Riveting tool 4. Jaw Case 7. Mandrel for nuts (x4)

2. Sleeve for mandrels 5. Nosepiece (x4) 8. Mandrel holder(x4)

3. Sleeve for nosepieces 6. Mandrel for studs (x3) 9. Spanners (x3)

Not shown - four starter packs of 10 steel rivet nuts - M3x0.5, M4x0.7, M5x0.8, M6x1.0.

1 2 3

AK396.V2 1
AK396.V2 - 1 - 071205 2

Résumé du contenu

Page 1 - AK396.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly mai

Page 2 - AK396.V2 - 1 - 071205

AK396.V2 - 1 - 0712053.1. Rivets (Figs 1 and 2)3.1.1. Assemble by fitting the jaw case (4) on to the tool and then fit sleeve (3). Select the correct

Page 3

4. MAINTENANCEAK396.V2 - 1 - 071205 4.1.1. Keep all pivots lightly oiled.4.1.2. The jaw case assembly should be cleaned and oiled at regular intervals

Commentaires sur ces manuels

Pas de commentaire

Sealey AK396 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Sealey AK396. Sealey AK396 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Sealey AK396